1783-BMS10CGN Stratix以太网I/P管理交换机

Allen-Bradley 1783-BMS10CGN是一种Stratix以太网I/P管理交换机。该以太网交换机共有十(10)个以太网端口，其中八(8)个快速以太网(FE)铜质端口和两(2)个千兆以太网(GE)端口。这种以太网交换机可用于实现安全性和弹性级别更高的工业架构。

它由外部24V直流电源供电，功耗为15瓦@ 24V DC/40°C(104°F ),功耗为20瓦。它的功耗为20瓦。1783-BMS10CGN配有一个集成报警继电器，触点额定值为1 A @ 30V DC或0.5 A @ 48V DC。

支持千兆以太网(GE)的组合端口可以安装小型可插拔(SFP)收发器，用于光纤层。也可以安装1784-SD1，用于保存以太网交换机的配置，方便将配置转移到其他类似的被管理以太网交换机。

对于以太网连接，推荐的电线组件是符合IEC 60603-7标准的RJ45连接器和符合TIA 568-B.1标准的两(2)对或四(4)对5e类最小电缆或符合ISO/IEC 24702标准的5类电缆。对于警报继电器的端接信号线，推荐的线尺寸为0.5-0.8平方毫米。或20-18 AWG实心或绞合、UL/CSA额定型1007或1569双绞线铜设备布线材料(AWM)线，6.3毫米(0.25英寸。)0.5毫米(0.02英寸。)条长。对于DC电源连接，合适的导线尺寸为0.5…0.8平方毫米。或20-18 AWG实心或绞合铜线，绝缘等级为75°C(167°F)或更高，绝缘厚度为1.2毫米(3/64英寸)。)带长6.3毫米(0.25英寸。)0.5毫米(0.02英寸。).

1783-BMS10CGN交换机上共有10个端口。其中八个端口是铜质(RJ-45)端口，它们支持快速以太网。其中两个端口是组合端口，它们支持铜缆和光纤连接。组合端口支持的网络速度是千兆以太网。1783-BMS10CGN交换机采用开放式外壳，其额定温度符合T4北美温度标准。1783-BMS10CGN交换机的重量和尺寸分别为3.05磅和5.1 x 3.6 x 5.345英寸。1783-BMS10CGN开关适用于12至48伏DC之间的DC输入电压。开关的电流消耗在0.5到2安培之间。1783-BMS10CGN交换机的典型功耗为15瓦，可达20瓦。交换机可以承受的环境温度为60摄氏度。在较高的环境温度下，开关性能会下降，开关也会损坏。

The Allen-Bradley 1783-BMS10CGN is a Stratix Ethernet I/P managed switch. This ethernet switch features a total of Ten (10) Ethernet ports with Eight (8) Fast Ethernet (FE) Copper ports and Two (2) Gigabit Ethernet (GE) ports. This Ethernet switch may be used for implementing industrial architecture with increased level of security and resiliency.

It is powered by an external 24VDC supply voltage with a power consumption of 15 Watts @ 24V DC/ 40 °C (104 °F) with maximum consumption of 20 Watts. It has a power dissipation of 20 Watts. The 1783-BMS10CGN has an integrated alarm relay with contact rating of 1 A @ 30V DC or 0.5 A @ 48V DC.

The combo ports which supports Gigabit Ethernet (GE) may be installed with Small Form-factor Pluggable (SFP) transceiver, used for fiber-optic layer. It may also be installed with a 1784-SD1, used for saving the ethernet switch’ configuration and convenient transfer of configuration to other similar managed ethernet switch.

For Ethernet connection, recommended wire assembly is RJ45 connector according to IEC 60603-7 and Two (2) or Four (4) pair Category 5e minimum cable according complying to TIA 568-B.1 or Category 5 cable according to ISO/IEC 24702. For terminating signal wires to the alarm relay, recommended wire size is 0.5-0.8 mm. sq. or 20-18 AWG solid or stranded, UL/CSA-rated style 1007 or 1569 twisted-pair copper appliance wiring material (AWM) wire, 6.3 mm (0.25 in.) ±0.5 mm (0.02 in.) strip length. For DC power connection, appropriate wire size is 0.5…0.8 mm sq. or 20-18 AWG solid or stranded copper wire with insulation rating of 75 °C (167 °F) or greater, and maximum insulation thickness of 1.2 mm (3/64 in.) with strip length of 6.3 mm (0.25 in.) ±0.5 mm (0.02 in.).

There are a total of 10 ports on the 1783-BMS10CGN switch. Eight of these ports are copper (RJ-45) ports and they support Fast Ethernet. Two of the ports are combo ports and they support both copper and fiber connectivity. The network speed supported by the combo ports is Gigabit Ethernet. The 1783-BMS10CGN switch comes in an open enclosure which is rated with the T4 North American temperature code. The weight and dimensions of the 1783-BMS10CGN switch are 3.05 pounds and 5.1 x 3.6 x 5.345 inches, respectively. The 1783-BMS10CGN switch works with DC input voltages between 12 and 48 Volts DC. The current consumption of the switch ranges from 0.5 to 2 Amps. The typical power consumption of the 1783-BMS10CGN switch is 15 Watts which can go up to a maximum of 20 Watts. The maximum ambient temperature which the switch can tolerate is 60 degrees Celsius. At higher ambient temperatures, the switch performance will degrade and the switch can also be damaged.